Additional Images

Chevy Big Block Vortech V-30 112A Race Bracket Assembly Kit

This Vortech mounting bracket & cog drive kit with a V-30 112A head unit setup for the Big Block Chevy Engine that fits 9.8 & 10.2 deck height engines will get you serious power in this bolt-on kit! This is the tuner kit that will require a custom tune done locally after you install the kit, and does not include a programmer, fuel injectors, high-performance fuel pump, intercooler, or piping.

Vortech Superchargers continues the quest to get more power options to Chevy racers with a new Billet Mounting Bracket Assembly engineered to install the respected V-30 Centrifugal Supercharger onto Big Block Chevy engines. The V-30s have proven to be the most reliable, efficient and consistent supercharger even under the toughest racing conditions and is specifically designed for modified performance engines that crave extreme boost. Available for Chevy Big Block engines, the Vortech Superchargers V-30 Mounting Bracket Assembly give drag racers and auto enthusiasts the edge needed to dominate the competition. Kits range from 1500 – 2800 HP.
Shipping: FREE continental USA ground shipping on ALL Vortech Supercharger Systems!
Was: $9,510.99
Sale: $9,489.99
Save: 0%
Save: $21.00

Free Basic Shipping


There are many options available for Vortech supercharger kits. If you have any questions please email [email protected] or call 760-586-5617.

For those looking for Vortech V-30 efficiency and power in a side-slinger mounting configuration, look no further! The Vortech V-30 Big Block Chevy Race Bracket Assembly is compatible with all Vortech V-30 Series Race Superchargers. The Billet aluminum twin-plate construction fits 9.8 and 10.2 deck height engines, and is both stylish and functional even at the highest levels of competition!

Billet Aluminum Twin-Plate construction
Fits 9.8 & 10.2 deck height engines
Dual-Bearing Billet Aluminum Idler with Flanges, Hard Anodized
Drive Belt Idler Adjustment Screw, Arbor and Spacers
Billet Water Crossover Assembly
Billet Aluminum, Hard Anodized, 50mm Cog drive
High Grade Mounting Hardware

Vortech Superior Technology
The V-30 112A Supercharger is a new compressor, replacing the existing V-28 112, and features a plethora of cutting-edge technology, including its technologically advanced, high-efficiency, 5-Axis machined billet impeller and high-diffusion housing developed in our SAE-J1723-compliant supercharger test cell.

Built to address the needs of the over 1,000HP racer, the V-30 is a clean sheet design that incorporates many years of racing compressor knowledge. The patented design employs a unique impeller shaft support system that is robust enough to endure the speeds and accelerations associated with high horsepower drag racing and the durability to perform well in the offshore boat-racing world. The modular design allows fitment of a wide range of compressor stages. Another revolutionary feature of the V-30 series is the new Nano-Tolerance Technology (NTT) that allows Vortech to minimize clearances inside the supercharger, without raising the chances of internal component compromise. This further raises the efficiency of what were already the most efficient superchargers available to new, unprecedented levels. What this means to you is less heat, lower IATs, and even more power at the same boost level.

The V-30 Superchargers also benefit from the Diverging Diffusion Technology (DDT) impeller/volute performance system with engine specific tunability. All V-30 series superchargers share a 4.21:1 internal step-up ratio and are engine oil lubricated or an auxiliary system can be fabricated. Like the V-1 family, the V-30 can have different compressor stages.

The V-30 Enhanced Air Inlet System is designed to work directly in conjunction with gear-drives and other front-facing mounting configurations to allow the V-30 Superchargers increased air induction capacity for each compressor.

Other, less efficient superchargers may be able to provide equal or greater levels of boost, but do so at higher discharge temperatures and with greater parasitic power loss.

Racers who switch from a competing supercharger to the 112A will be capable of lower ET's and faster top speeds due to its higher efficiency, lower discharge temperatures, and greater power potential.

The extreme durability of the V-30 supercharger design allows a single head unit to be used for multiple quarter-mile passes before being replaced, under the same conditions that cause competing superchargers to wear down and need replacement after one or two passes.

Vortech Dealer information
Not any shop can become an Authorized Vortech Installing Dealer; you need to be knowledgable in both naturally aspirated and boosted high performance vehicles, and have the staff to support customers with both in store and phone support. Vortech is very strict about who they allow as dealers. Most online only or mail order companies are unable to qualify as dealers, but you are welcome to stop by our shop to talk about your application or view our supercharger kits. TREperformance has been building high performance vehicles for over 15 years, everything from simple engine upgrades to 1,000 horsepower drag cars. We have been selling superchargers and building blown motors for over a decade, so you know the dealer you are buying from has the knowledge to get you the right kit for your application.

TREperformance is an Authorized Priority Dealer of Vortech/Paxton superchargers.
Custom made and shipped direct from Vortech in 3-5 business days!


Shipping Information

  • Item Requires Shipping
  • 65.0 lbs.
  • W24.0000” x H12.0000” x L12.0000”
  • Free Basic Shipping
  • This item ships in its own box.
  • FREE continental USA ground shipping on ALL Vortech Supercharger Systems!

  • Have a question? Ask the Pros
  • 877-514-9494Mon - Fri 8:00 AM - 4:00 PM PST